1

인덕션 호브가 작동하지 않는 이유?

인덕션 호브가 작동하지 않습니까?? What can be the causes

Before seeing the reasons why an induction hob does not work, 그것 is good to understand how induction cookers work.

인덕션 호브는 어떻게 작동합니까??

Firing is guaranteed by the coils located under the ceramic glass top. The electrical energy that powers the coils generates a magnetic field that heats the pots.

In this way an 인덕션 호브 can guarantee an excellent efficiency, ~에 대한 90%, while a traditional gas cooker has an efficiency of 40%, as a good part of the heat produced is dispersed into the environment.

게다가, cooking with an induction hob is faster and more precise, because the heat spreads evenly over the pan. 그 다음에, the absence of flames avoids the risks of any gas leaks. Induction hobs offer many advantages, but like all appliances, they can be subject to breakdowns and malfunctions.

Why doesn't an induction hob work?

There can be several reasons why an induction hob does not turn on:

  • faulty power supply
  • 호브 클램프가 손상되었거나 잘못 연결됨
  • 결함이 있는 전기판

이러한 경우, 할 수 있는 전문 기술자에게 의뢰하는 것이 좋습니다. 모든 실패 확인 and carry out the appropriate operations to solve it.

뿐만 아니라, 주방을 조작하는 키보드가 더러워진 액체나 이물질로 인해 인덕션 호브의 터치 인식이 작동하지 않을 수 있습니다..

이 문제를 해결하려면, just clean the hob with special detergents and a microfibre cloth. It may also happen that the induction hob does not recognize the pot. To cook on an induction hob, 사실은, it is necessary to use enameled iron, 주철, and stainless steel pots and pans. Those in ceramic or terracotta should be avoided.

 

The induction hob does not heat up

 

Are the cooking zones of the induction hob no longer cooking properly? Let's try to investigate the possible causes behind this problem.

POSSIBLE CAUSES OF THIS PROBLEM:

USED POTS AND PANS ARE NOT SUITABLE

 

THE POWER OF THE INDUCTION COOKER IS TOO LOW

 

THE HOB HAS BEEN CONFIGURED INCORRECTLY

 

THE ELECTRICAL SYSTEM IS NOT UP TO STANDARD

 

THE ELECTRICAL CLAMP IS NOT TIGHTENED PROPERLY

 

THE ELECTRONIC BOARD IS FAULTY

 

ATTENTION
Before working on the appliance, make sure it is disconnected from the mains.
Danger of electrocution.
Wear suitable gloves,
cut hazard.

Used pots and pans are not suitable

5

 

If you use aluminum pots and pans, you should know that these are not suitable for induction cookers. For this type of appliance, it is preferable to prefer materials in cast iron or steel. It is in fact necessary that the pots have a relatively high ferrous content in order for them to heat up properly.

Tip
To find out if the pots and pans are compatible with induction hobs, place a magnet on the lower end of the pan: if it sticks, they should be compatible.

Warning: some stoves are more sensitive than others. For this reason, even if the tools have a specific symbol for induction, it is recommended to try them on the hob to verify that they are actually suitable.

The power of the induction cooker is too low

4

 

Each hob has a different power, which depends on the number of electronic boards it is equipped with: a hob can have, 예를 들어, six cooking zones operating independently (최대 전력으로), since they have an individual electronic power unit.

On other cookers, the cooking zones work in pairs since there is only one electronic unit for every two burners. This means that, by setting one zone to maximum power, the other cooker that shares the same electronic board will not be able to do the same and will be less powerful.

There are also hobs where the cooking zones work in perfect harmony: all the burners are connected to a single power unit, and only one of the cookers can therefore operate at maximum power.

Buy a power board for the hob

The hob has been configured incorrectly

6

 

You need to know that some hobs can be programmed to operate from 2,500 watts (16 amps) NS 7,200 watts. If you find that your appliance is heating too little, it may be that the hob you just bought has been 너무 낮은 전력으로 구성. 장치에 설정된 전원을 이해 및/또는 수정하려면, 사용 설명서를 참조할 필요가 있습니다!

전기 시스템이 표준에 맞지 않음

2

 

최적의 기능을 하려면, 인덕션 호브는 올바른 전압으로 전원을 공급해야 합니다., 일반적으로 230 볼트. Some stoves will not work properly if the voltage is below 210 볼트, 충분히 가열되지 않기 때문에.

Very often this voltage problem occurs in winter since the system is stressed by domestic heating, consequently causing a significant voltage drop.

To check the voltage of the electrical system you can use a multimeter in voltmeter mode and measure the voltage present in the kitchen from any electrical outlet. Then place several pots on the stove and activate the cooking zones. If the voltage drops dramatically towards a value of 210 볼트 (이하), this is the reason why the induction cooker does not heat enough. 이 경우, we recommend that you consult your electricity supplier.

The electrical clamp is not tightened properly

7

 

It may happen that the connection clamp on the hob or on the wall connection is not tightened correctly, causing only partial operation of the appliance. 이 경우, tighten the visible union screws and try again.

If your stove is new and only two of the four cooking zones work, we recommend checking that the wiring diagram is correct as the appliance may have been connected incorrectly.

Advice It is
better not to always use the same cooking zone but to make them work in rotation; if the same burner is always used, its coil could overheat and deteriorate rapidly.

The electronic board is faulty

3

 

NS electronic board undergoes a lot of stress during cooking. Over time, this could lead to a loss of stamina. 이 경우, the hob will indicate an error code on the display and will only operate at low power, therefore at temperatures that are not sufficient to heat a pot. If you have difficulty diagnosing this component, do not hesitate to contact our customer service or a technician authorized by the manufacturer of the appliance.

댓글 없음

댓글 달기